Top 10 typical forklift mishaps ， forklift operation ought to take note of these matters ！.

Do not ignore the forklift at work. If the operation is not good, there will be significant mishaps in minutes, and there are lots of crashes entailing forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, causing a moving crash.
Situation 2: In order to preserve the equilibrium of the forklift when lifting heavy goods, the employees utilized their body weight as the weight, which practically caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an mishap.
Case 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not see the forklift.
Instance 6: The forklift lifts the personnel unlawfully, the forklift vehicle driver does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift rolls over.
Instance 7: The forklift motorist did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift operation need to focus on these matters ：.

Beginning.
1. Before starting, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and then begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be risk-free before beginning.
3. When the forklift starts with a tons, the driver must first verify that the lots is steady and reputable.
4. The beginning should be sluggish and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the pole ought to be slanted backward. .
2. Do not lift the fork expensive when driving. When entering and leaving the task website or while driving, be careful that there will certainly be no obstacles in the sky. When the lots is taking a trip, the fork should not be elevated too high, which will impact the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed sharp turns are forbidden. High-speed doglegs will cause the automobile to shed side security and topple. .
5. When the forklift is downhill, it is strictly forbidden to shut off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special situations.
6. When the forklift is running, it should comply with the traffic rules in the factory and should maintain a specific security range from the lorry ahead. .
7. When the forklift is running, the lots must be in the lowest position that does not impede the driving, and the gantry ought to be appropriately slanted back. The tons will not be increased except when stacking or packing. .
8. The height of the load should not block the chauffeur's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to depend on the fork to hold things and play a balancing role. .
12. If issues are found, they will certainly be fixed and reported in a timely manner, and they will certainly never operate with ailments or hide them.

loading and dumping.
1. When fork-loading products, the distance in between both forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or make use of a fork top or pull. In unique situations, safety indication must be established to remind surrounding pedestrians. .
3. In the process of packing and unloading products, the forklift must be stopped with the brake. .
4. The speed of the automobile should be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be kept in mind that the fork suggestion need to not touch various other items or items. The tons should be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted onward slightly when the load is decreased to permit simple positioning of the load and extraction of the forks. .
6. It is prohibited to fork items at high speed and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to loaf the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to use forks to lift workers to take part in high-altitude procedures to stay clear of high-altitude falling accidents. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you need to discharge the goods or reduced the fork framework.
2. Draw the emergency brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not exceed 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance ought to be checked, and fuel, lubing oil and air conditioning water Stand-on Electric Pallet Stacker must be included.
2. Inspect the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are typical.
5. After the forklift is running, the outside leakage needs to additionally be inspected Stand-on Electric Pallet Stacker and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the cargo ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the tendency of " cost-free turning";.
6. Adding and down the slope should be slow-moving and consistent, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the automobile should be driven in reverse when declining;.
8. When the forklift workers lug the goods and progress, if they encounter big or hefty products and most likely to the driver's line of vision, they should take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork procedure is not allowed.
2. It is not enabled to raise the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not enabled to make use of stopping force to exile round or easy-to-roll things.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on inclines
.
Parking is not permitted under the list below problems.
1. Contours, slim roadways, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the section with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844